SAILBOATS, including trailer & motor
	GENERAL:
	Do a general cleaning of hull, deck and topsides using a mild detergent & bleach
	Make sure drains and scuppers are clear
	Put on a good coat of wax in all hull topsides
	Clean and polish metal with a good metal polish
	Clean teak (and other wood) and reseal?
	Clean windows and hatches, clean screens
	Clean canvas, bimini and dodger (use same soap)
	Clean sail covers
	Clean interior including bilges
	Make sure registration is current and onboard
	HULL:
	Check for hull abrasions, scratches, gouges, etc. and repair
	Check for blisters and refinish is necessary
	Check rub rails, has anything come loose?
	Check swim ladder
	Check rudder and fittings
	Touch up or recoat antifouling paint
	DECK, FITTINGS, SAFETY EQUIPMENT:
	Check stanchion, pulpits and lifelines for integrity
	Check ground tackle, anchor, rode and backup anchor / rode, etc
	Check lines, fenders, etc.
	Check chainplates, cleats and other deck fittings
	Check hull/deck joint
	Check deck, windows, and port lights for leaks
	Clean and grease winches
	Check and lubricate blocks, pad eyes, etc.
	BELOW DECKS:
	Check, test and lubricate seacocks
	Check all thruhull fittings
	Check condition of hoses and clamps
	Check bilges pumps for automatic and manual operation
	Check limber holes and make sure they are clear of debris
	ELECTRICAL SYSTEM AND COMPONENTS:
	Check battery water level – the single most often ignored task
	Check/recharge batteries
	Check terminals for corrosion, clean and lubricate
	Inspect all wiring for wear and chafe
	Check shore power and charger
	Check for spare fuses or breakers
	Check all lighting fixtures (including navigation lights)
	Check all electronics for proper operation
	Inspect antennas
	REQUIRED AND RECOMMENDED EQUIPMENT:
	Sound signaling device – spare air can for air horn
	Check distress signals and expiration date
	Check PFDs (lifejackets)
	Inspect life rings and cushions
	Check fire extinguishers certification and recharge if necessary
	Check and adjust compass
	Check navigation lights
	Check and replace first aid supplies
	Check bailer and hand pump
	INBOARD ENGINE:
	Change oil & filters
	Check and change fuel filters
	Check cooling system change coolant as necessary
	Record engine maintenance log, especially date & hours of last oil changes
	Check belts for tension
	Check transmission fluid
	Check impeller
	Check and clean water strainer
	Check bilge blower
	Adjust valves, general service engine
	OUTBOARD MOTOR:
	Change Oil - 4 stroke motor only
	Discard Fuel at end of season
	Clean inside of motor housing - spray/WD40(for mud-dobbers)
	Replace spark plugs
	Check plug wires for wear
	Check prop for nicks and bends
	Change/fill gear lube
	Inspect fuel lines, primer bulb and tank for leaks
	Lubricate and spray moveable parts
	HEAD SYSTEM:
	Checked for smooth operation - lubricate and clean as necessary
	If equipped with treatment system, have chemicals on hand
	Y-valve operation checked, valve labeled & secured
	WATER SYSTEM:
	Flush water tank
	Shock the drinking water tank. Spa shock breaks down in a few days then flushed
	Check water system and pump for leaks and proper operation
	TRAILER:
	Check for current registration
	Check rollers and pads
	Check and lubricate wheel bearings
	Clean and lubricate winch
	Lubricate tongue jack and wheel
	Test lights and electrical connections
	Check tire pressure and condition
	Check brakes (if equipped)
	Check safety chains
	Check tongue lock
	SAILS:
	Check general condition
	Look for wear and chafing
	Check battens and batten pockets
	Check all sail attachments, including grommets, rings, and all reef-points
	Inspect all of the stitching on the sail edges and all seams. Pay close attention to the leech of the headsail
	Inspect bolt rope
	MAST AND RIGGING:
	Check mast and spreaders for corrosion or damage
	Inspect spreader boots and shrouds
	Inspect rivets and screw connections for corrosion
	Check reefing points and reefing gear
	Clean and lube sail track
	Check rigging, turnbuckles and clevis pins for wear and corrosion
	Inspect stays for fraying and “fish hooks”
	Check forestay and backstay connections
	Check masthead fitting and pulleys
	Check and lubricate roller furling
	Check halyards and consider replacing or swapping end for end
	Tape turnbuckles, cotter pins, and spreaders